KILZ® DECORATIVE CONCRETE COATING
KILZ® Decorative Concrete Coating is ideal for Interior/Exterior surfaces such as porous concrete, masonry, stone pavers and brick. Ideal for garages, driveways, walkways, patios, porches and pool decks. DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to forklifts. Surfaces may become slippery when wet. Use caution when walking on surface when moisture is present.
Available in Tan and Gray
Finish
Available in Tan and Gray Base. Textured, Slip-Resistant Finish.
Best For Use On
Ideal for Interior/Exterior surfaces such as porous concrete, masonry, stone pavers and brick. Ideal for garage floors, driveways, walkways, patios, porches and pool decks. DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to forklifts.
Coverage
40-60 Sq. Ft./Gal.
TECHNICAL DOCUMENTS
THE FOLLOWING STEPS AND PRODUCTS ARE REQUIRED:
- All surfaces must be clean, sound, dry and free of any dirt, oil, and grease.
- Uncoated Concrete or Masonry Surfaces: Allow new surfaces to cure 30 days. Clean and etch surface using a product such as a muriatic acid etcher (read and follow all manufacturer's label directions) to achieve a textured profile similar to 150 grit sandpaper.
- Previously Coated Surfaces: If surface is in sound condition, use a product to clean and prepare the surface. If the coating is failing or peeling, use a paint stripper to remove old coating or scrape/sand down to a sound concrete surface. Scuff sand glossy surfaces. Clean and spot etch any exposed concrete. Remove all dust with a damp cloth, allow to dry.
†WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
Application
- DO NOT THIN.
- Do not apply in extreme weather conditions. Use product when air temperature is between 50-90° F. DO NOT APPLY IN DIRECT SUNLIGHT.
- Intermix all cans of same product to ensure color uniformity. Stir before applying.
- For hairline cracks up to 1/8", fill in with coating using a nylon/polyester brush and allow to dry completely prior to roller application.
- Apply a product such as KILZ® Concrete & Masonry Bonding Primer to increase adhesion of topcoat to the surface.
- Pour directly from the container onto the surface or apply using a roller tray.
- Apply a first coat using a 1/4" adhesive roller cover, or nylon/polyester brush. Note: The first coat will act as the base coat and it will not completely cover the surface by design. Avoid over application on the first coat.
- Apply in 4' by 4' sections. Begin with the roller in the center of the section and roll outwards in random directions. Avoid regular patterns and knock down hard edges using the roller.
- Allow first coat to dry before applying the second coat using the same method.
- While 2 coats are necessary, additional coats may help hide previous surface imperfections or cover over dark colors.
- For large projects, consider using a texture sprayer with a 4mm tip. Spray in 4' by 4' sections and back roll with an adhesive roller cover.
- An annual touch-up may be required in areas subject to high traffic.
Read More
Dry Time at 77°F (25°C), 50% RH
- Dries to touch in 1 hours.
- Wait 3-4 hours before recoat.
- The floor may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting surface to automotive tires, heavy foot traffic or repositioning furniture.
- Premature heavy traffic will cause paint failure requiring spot recoating.
- Wait at least 30 days before cleaning/rinsing with a cleaner.
- Additional dry time may be needed in cooler temperatures and higher humidity. Premature heavy traffic may affect film integrity.
Read More
Clean Up & Disposal
- Clean all tools and equipment with soap and clean water.
- Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.
Read More
Read More
WARRANTY
*Limited Warranty
For one year from the date of purchase, Masterchem Industries LLC warrants to the original residential consumer purchaser (1) that the product meets Masterchem Industries LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event that this product proves to be defective within one year from the date of purchase, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: [email protected]. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
General Information
IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS
†Warning!
If you scrape sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respir tor to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
CAUTION! Surfaces may become slippery when wet. Use caution when walking on surface when moisture is present.
Warning! Irritant!
HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
First Aid
- If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
- In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention.
- For skin, wash thoroughly with soap and water.
- If swallowed, get medical attention immediately.
Caution
KEEP OUT OF REACH OF CHILDREN.
DO NOT TAKE INTERNALLY.
Read More
PRODUCT SPECIFICATIONS
Int/Ext
Int/Ext
2 Coats At 40 Sq. Ft./Gal. (Wet)
40 Mils
2 Coats At 40 Sq. Ft./Gal. (Dry)
16 Mils
2 Coats At 60 Sq. Ft./Gal. (Wet)
27 Mils
2 Coats At 60 Sq. Ft./Gal. (Dry)
11 Mils
VOC
<50 g/L
Brush
Synthetic
Roller - Smooth
1/4" Adhesive Roller
% Solids by Volume:
39%
% Solids by Weight:
54%
Weight / Gallon (lbs)
11
Viscosity
85-100 KU
Flashpoint
N/A
Sheen @ 85°
<5
Gloss @ 60°
<5
Resin Type
Acrylic
PRIMER TIPS
The Right Applicator Can Make a Big Difference
Find tips from paint professionals and discover the different types of paint brushes in market along with the best paint brushes to use for various projects.
KILZ BLOG
