KILZ® MASONRY, STUCCO & BRICK FLAT PAINT
KILZ® Masonry, Stucco & Brick Flat paint is a high-quality, acrylic latex paint with excellent hiding properties. This interior/exterior, self-priming, mildew resistant finish also provides excellent adhesion and water repellency on properly prepared, smooth, rough and textured masonry, stucco and brick surfaces. This water-based formula is designed to accentuate all textured surfaces while achieving a natural look. It is alkali-resistant up to pH 12.0, easy to apply, and cleans up with soap and water.
Available in Grey, Tan, and White
Finish
Available in Gray, Tan, and White. Flat Mildew-Resistant Finish.
Best For Use On
Ideal for properly prepared, smooth, rough and textured masonry, stucco and brick surfaces, as well as adjacent wood and metal. Do not use on horizontal surfaces subject to foot traffic.
Coverage
250-400 Sq. Ft./Gal.
TECHNICAL DOCUMENTS
THE FOLLOWING STEPS AND PRODUCTS ARE REQUIRED:
- Allow new stucco and masonry to cure for 30 days before painting.
- Remove all loose, peeling paint. Power wash to remove chalk. Remove dirt, grease and mildew stains with KILZ Concrete & Masonry Cleaner & Degreaser.
- On galvanized metal, use a diluted solution of KILZ Concrete & Masonry Cleaner & Etcher to prepare the surface. Rinse thoroughly and allow a minimum of 24 hours to dry.
- Cracks and gaps wider than 1/16" should be routed open, dusted and patched with a quality patching compound. Use an acrylic caulk around windows, doors and trim. Scuff sand glossy surfaces.
- If chalk remains on the surface, prime with a KILZ Premium Primer. Prime all patched areas as well as adjacent wood and metal surfaces. If previously sealed or coated, check manufacturer’s specifications before painting.
†WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
Application
- DO NOT DILUTE. Intermix all cans of same product to ensure color uniformity. Stir paint before and occasionally during application.
- For best results, apply when air and surface temperatures are between 50-90°F. Do not use if rain or heavy dew is expected within 24 hours.
- Apply using a high quality 3/4"-1" nap roller (rough surfaces) or 3/8"-1/2" nap roller (smooth surfaces), nylon/polyester brush or airless sprayer (.015"-.021" spray tip, 60 mesh filter). Apply a second coat, if necessary.
- Maintain a wet edge to avoid lap marks. Do not re-spread or re-work paint.
- COVERAGE: Rough surfaces: 250-300 sq. ft; Smooth surface 400 sq. ft.
Read More
Dry Time at 77°F (25°C), 50% RH
- Dries to touch in 1 hours.
- Wait 2-4 hours before recoat.
- After two weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent.
- Additional dry time may be needed in cooler temperatures and higher humidity. Premature heavy traffic may affect film integrity.
Read More
Clean Up & Disposal
- Clean equipment and paint spatters with warm, soapy water.
- If spilled, contain material and remove with an inert absorbent.
- Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations.
- Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.
Read More
Read More
WARRANTY
*Limited Warranty
For one year from the date of purchase, Masterchem Industries LLC warrants to the original residential consumer purchaser (1) that the product meets Masterchem Industries LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event that this product proves to be defective within one year from the date of purchase, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: [email protected]. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
General Information
IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS
†Warning!
If you scrape sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respir tor to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
CAUTION! Surfaces may become slippery when wet. Use caution when walking on surface when moisture is present.
Warning! Irritant!
HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
First Aid
- If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
- In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention.
- For skin, wash thoroughly with soap and water.
- If swallowed, get medical attention immediately.
Caution
KEEP OUT OF REACH OF CHILDREN.
DO NOT TAKE INTERNALLY.
Read More
PRODUCT SPECIFICATIONS
Int/Ext
Int/Ext
At 250 Sq. Ft./Gal. (Wet)
6.4 Mils
At 250 Sq. Ft./Gal. (Dry)
2.0 Mils
At 400 Sq. Ft./Gal. (Wet)
4.0 Mils
At 400 Sq. Ft./Gal. (Dry)
1.2 Mils
VOC
<50 g/L
Brush
Nylon / Polyester
Roller - Smooth
3/8" - 1/2" nap
% Solids by Volume:
30%
% Solids by Weight:
44.5%
Weight / Gallon (lbs)
10.7
Viscosity
95-105 KU
Flashpoint
N/A
Sheen @ 85°
0-6
Resin Type
Acrylic Latex
PRIMER TIPS
The Ultimate Painting Checklist for Any Project
What do I need to paint a room? This is a question that many ask when starting a new project. Find the ultimate painting checklist to prepare for any paint project.
KILZ BLOG
