KILZ® Decorative Concrete Coating

Surface Preparation

WHERE TO USE

• Interior/Exterior surfaces such as porous concrete, masonry, stone pavers and brick. Ideal for garages, driveways, walkways, patios, porches and pool decks.

PROPER SURFACE PREPARATION IS REQUIRED

• All surfaces must be clean, sound, dry and free of any dirt, oil, and grease.
• Uncoated Concrete or Masonry Surfaces: Allow new surfaces to cure 30 days. Clean and etch surface using a product such as a muriatic acid etcher (read and follow all manufacturer’s label directions) to achieve a textured profile similar to 150 grit sandpaper.
• Previously Coated Surfaces: If surface is in sound condition, use a product to clean and prepare the surface. If the coating is failing or peeling, use a paint stripper to remove old coating or scrape/sand down to a sound concrete surface. Scuff sand glossy surfaces. Clean and spot etch any exposed concrete. Remove all dust with a damp cloth, allow to dry.

Application

• DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to forklifts. Surfaces may become slippery when wet. Use caution when walking on surface when moisture is present.

• DO NOT THIN Product is formulated for use at package consistency.

• For hairline cracks up to 1/8”, fill in with coating using a nylon/polyester brush and allow to dry completely prior to roller application.

• Do not pour product directly on surface; always use a roller tray.

• Apply a first coat using a 1/4" adhesive roller cover or nylon/polyester brush. Note: The first coat will act as the base coat and it will not completely cover the surface by design. Avoid over application on the first coat.

• Apply in 4’ x 4’ sections. Begin with the roller in the center of the section and roll outwards in random directions. Avoid regular patterns and knock down hard edges using the roller.

• Allow first coat to dry before applying the second coat using the same method.

• While 2 coats are necessary, additional coats may help hide previous surface imperfections or cover over dark colors.

• Use a Texture Sprayer with a 4 mm spray tip for large projects. Spray in 4’ x 4’ sections and back roll with an adhesive roller cover. Keep material flow adjustment on the gun open. Adjust air flow on gun to about 50% - or as low as possible to maintain full spray pattern. Spray 18” – 30” from wall. Overlap spray pattern 50%.

• An annual touch-up may be required in areas subject to high traffic.

Dry Time @ 77°F (25°C), 50% RH

To Touch: 1 hour

To Recoat: 3-4 hours

• Longer dry time required in cooler temperatures and in higher humidity.

• The floor may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting surface to automotive tires, heavy foot traffic or repositioning furniture.

• Premature heavy traffic will cause paint failure requiring spot recoating. Wait at least 30 days before cleaning/ rinsing with a cleaner.

Clean-Up & Disposal

• Clean all tools and equipment with clean water. For disposal of empty containers and unused product, contact your household refuse collection service.

Cautions / Limitations

• DO NOT THIN.

• Intermix all cans of same product to ensure colour uniformity. Stir before applying.

• Use product when air and surface temperatures are between 50-90° F.

• DO NOT apply in direct sunlight.

• DO NOT use on vertical surfaces or areas subject to hydrostatic pressure.

• NOT for industrial use or areas subject to forklifts.

LIMITED WARRANTY

Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product for one (1) year from the date of purchase when applied according to the label instructions and specifications. In the event that this product proves to be defective during the warranty period, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow the exclusion or limitations on how long a warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this document are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To make a claim under this warranty, write to: Technical Service, Masterchem Industries LLC, 3135 Old Highway M, Imperial, MO 63052-2834; or email Technical Service at techservice@masterchem.com.

^†Warning!

This product contains chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm.
 


USE ONLY WITH ADEQUATE VENTILATION

Warning! Irritant!

CAUTION IRRITANT Avoid contact with eyes. May cause eye, nose and throat irritation. Avoid breathing of dust, vapors or spray mist. Open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/ mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH / MSHA TC -23C or equivalent) during and after application. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Wash thoroughly after handling and before smoking or eating.

^†Warning!

If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.



First Aid

If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.

KEEP FROM FREEZING. If frozen, let thaw at room temperature. 

KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.

• Base

  Acrylic

• Int/Ext

  Int/Ext

• Color

  Gray | Tan

• Coverage Rate

  Up to 60 Sq. Ft./Gal.

• Coverage Low to High

  40 to 60 sq. ft./Gal (2 coats required)

• Mils Wet @ 40 Sq. ft

  40

• Mils Dry @ 40 Sq. ft

  16

• Mils Wet @ 60 Sq. Ft

  27

• Mils Dry @ 60 Sq. Ft

  10

• VOC

  50 g/L

• Volume Solids

  39.0%

• Weight Solids

  54.0%

• Viscosity

  118-128 KU

• Flashpoint

  N/A

• Dry To Touch

  1 hour

• Dry To Recoat

  3-4 hours

• Brush

  Synthetic

• Roller - Smooth

  Adhesive Roller

• Spray Tip

  4 mm

• Spray Filter

  N/A

• Spray Pressure

  ‭40psi and 1.0 GPM

• Min Application Temp

  50º F

• Max Application Temp

  89.6º F