KILZ® UPSHOT® Interior
Overhead Stain Sealer

PREPARATION

The surface must be clean, free of dust, grease, wax, peeling paint, mold, mildew, wallpaper paste. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.
 

WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Centre at 1-800-424-LEAD or log on to www.epa.gov/lead.

APPLICATION

Eye protection is recommended. For best results, use at room temperature. Cover adjacent areas to protect from overspray. Shake can vigorously for 1 minute after mixing ball begins to rattle and often during use. Hold can upright, moving from side-to-side while spraying lightly and evenly about 30 cm (12") from area being painted. Two to three thin coats produce best results. Topcoat with latex or oil-based paint after 60 minutes. NOTE: On some surfaces, spot priming may cause a non-uniform appearance in the final coat. To avoid this, prime the entire surface.

CLEAN-UP & DISPOSAL

Clear spray valve immediately after use by turning can upside down and spraying until only clear gas is released. If spray nozzle becomes clogged, remove and clean with mineral spirits or acetone. Do not stick pins or wire into can opening. Replace nozzle with valve opening pointed away from you. Clean fresh overspray with mineral spirits or paint thinner. Remove dried paint with paint remover, but test small area first to ensure paint remover does not damage substrate. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.

LIFETIME LIMITED WARRANTY

Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS.  This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Masterchem Industries LLC unless extended by a provincial consumer statute. To obtain warranty service, write to: Technical Services, Masterchem Industries LLC, 2750 Centre Avenue N.E., Calgary, AB T2A2L3, or email: techserve@masterchem.com.  Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

For warranty service, call: 1-866-977-3711, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

WARNING!

CONTENTS MAY CATCH FIRE. CONTENTS HARMFUL.CONTAINER MAY EXPLODE IF HEATED. Do not smoke. Do not get on skin or clothing. Do not breathe fumes. Do not puncture or burn. Keep away from heat, high intensity lights, flames, such as pilot lights, and any object that sparks, such as an electric motor. Vapours are heavier than air, and can travel at floor level to distant ignition sources. Use only in a well ventilated area. Do not use this product unless you can prevent build-up of vapours by opening all windows and doors to achieve cross-ventilation. Wear respirator, rubber gloves and protective clothing. Keep out of reach of children.

FIRST AID TREATMENT

Contains Aliphatic Hydrocarbons (Stoddard Type) and Acetone. If in eyes, rinse with water for 20 minutes. If on skin, rinse well with water. If inhaled, move person to fresh air.

HEALTHY INDOOR PAINTING PRACTICES

HOW TO REDUCE YOUR EXPOSURE

This Information Refers Only to Interior Alkyd (or Oil-based) Paint Containing 2-Butanone oxime (MEKO); MEKO is not found in any of the widespread latex or waterborne products.

• Always read, understand and carefully follow all ventilation requirements indicated on labels;
• Take measures to maximize the amount of fresh air where you paint; you should not rely on home heating or cooling systems to provide fresh air. Try to schedule painting so that you can open windows and doors to the outside;
• It is recommended that you create cross-ventilation when painting by opening windows and doors that are across from each other and/or using a fan to blow air outdoors (if there is no warning on the paint label instructing against the use of electric motor fans). Kitchen and/or bathroom fans that are vented outside can also help;
• Take fresh air breaks while painting and keep young children, pregnant women and people with breathing problems away from freshly painted rooms. Leave painted areas if you experience eye watering, headaches, dizziness or breathing problems;
• Cover your paint can during use and quickly dispose of rags and accessories after you have finished with your project. Unused or leftover alkyd paint can be disposed of through the paint recycling program in your province;
• Remember to continue using proper ventilation for two to three days after you finish painting;
• MEKO and other chemicals may still be present in low VOC (volatile organic compound) alkyd paint so remember to always create well-ventilated conditions;
• It is a misconception that infrequent use of alkyd paint poses no health risk. Proper precautions and ventilation are required every time the product is used.

PROTECTING CONSUMER HEALTH:

CODE OF PRACTICE FOR 2-BUTANONE OXIME (MEKO)

• Base

  Oil

• Int/Ext

  Int

• Colour

  White

• Coverage

  1.3 m² - 1.7 m²

• Finish @ 85°

  <10

• Min Application Temp

  10°C

• Max Application Temp

  32°C

• Dry To Touch

  15 - 30 min

• Dry To Recoat

  1 hour

• Max VOC (by weight)

  60%

• Volume Solids

  18.0% (+/-) 2%

• Weight Solids

  40.0% (+/-) 2%

• Flashpoint

  -104°C