KILZ® HIDE-ALL

KEY ATTRIBUTES - LEARN MORE

Hides
Previous
Color

Helps Block
Light/Med
Stains

KILZ® HIDE-ALL™ is a high hiding, fast drying, multi-surface latex primer sealer formulated to minimize problems caused by dark colors, minor surface marks, textures and porosity differences. Ready to brush, roll or spray, it can be topcoated after one hour with latex or oil-base paint. Use KILZ HIDE-ALL on interior surfaces including drywall, cured plaster, woodwork, masonry, concrete block, brick and previously painted surfaces. Not for use over glossy surfaces or on floors.

WHERE TO BUY

Please check availability before visiting your local retailer

Available in Gallons & Fives

Surface Preparation

  • All surfaces must be clean, free of dust, chalk,oil, grease, wax polish, mold and mildew, loose peeling paint, rust and all other foreign substances.

  • If washing is necessary, use a non-soapy detergent or TSP substitute. Rinse well and allow to dry.

  • Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.

  • Glossy Surfaces - Not Recommended: Use products such as KILZ® ADHESION, KILZ MAX® and KILZ® PREMIUM primers over properly prepared glossy surfaces.

  • Always wash mold or mildew covered surfaces with a mildew remover, rinse with water and allow to dry before priming.

  • Mold or Mildew Prone Surfaces - Not Recommended: use products such as KILZ PREMIUM and KILZ 2® primers over properly prepared, mold- or mildew-prone areas.

  • Masonry, Brick, Stucco and Plaster: KILZ HIDE-ALL may be used on clean, dry, aged interior masonry surfaces that have cured (dried) at least 30 days.

Application

  • Eye protection is recommended.

  • Only apply if surface, air and product temperatures are between 50° – 90°F (10° – 32°C).

  • Apply using a brush, roller or sprayer.

  • Only apply if surface, air and product temperatures are between 50°-90°F.

  • Brush – High quality Nylon/Polyester.

  • Roller – High quality 3/8-1/2" nap on smooth surfaces or 1/2-3/4" nap on semi-rough or porous surfaces.

  • Airless spray – .017 - .021 tip / 60 mesh filter @ 1,800 – 2,500 PSI.

  • DO NOT THIN. Product is formulated for use at package consistency. For spray applications, a small amount of water (no more than ½ pint per gallon) may be added.

  • Stir thoroughly before and occasionally during use.

  • Stains: KILZ HIDE-ALL is formulated to hide minor, non-bleeding scuffs and stains before topcoating; for heavier stains use a product such as KILZ MAX, KILZ PREMIUM, KILZ® ORIGINAL, KILZ COMPLETE® or KILZ ODORLESS® primers.

  • Tinting: May be tinted with up to 2 oz. (60 mL) of universal colorant per gallon. Tinting to a lighter shade than the topcoat is recommended.

  • Coverage: 300 - 400 sq. ft.(28 - 37 m2) per gallon depending on application method and surface porosity.

Dry Time at 77°F (25°C), 50% RH:

  • To Touch: 30 Minutes

  • Can be recoated or topcoated in one hour with latex or oil-based paint.

  • Application at lower temperatures, in high humidity or in poorly ventilated areas will affect dry time.

Clean up & Disposal

  • Clean equipment and paint spatters with warm, soapy water.

  • If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations.

  • Do not dispose of this product down a drain. Please consider donating any unused product.

  • For recycling or disposal information contact your local household refuse collection service.

Cautions / Limitations

  • IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS

  • DO NOT USE ON FLOORS

  • DO NOT USE WHEN AIR AND SURFACE TEMPERATURES ARE BELOW 50°F OR ABOVE 90°F

  • SHELF LIFE UNDER NORMAL CONDITIONS IS TWO YEARS UNOPENED