Logo

KILZ PRO-X® 110 Interior Flat

KILZ PRO-X® 110 Interior Flat

Bookmark and Share
      

KILZ PRO-X® 110 Interior Dead Flat is a high-hiding, non-reflective, latex paint for production environments with strong spray, spray back-roll and touch-up features. Ideal for walls & ceilings in high turnover properties.

Where to Buy

The Home Depot Find a Store   Buy Now

   Available in
    Gallons, Fives PX110 - MSDS   |   KILZ PRO-X® 110 INTERIOR FLAT TDS

PRODUCT SPECIFICATIONS
Base Water
Int/Ext Int
Color White
Coverage - Low 300 sq. ft.
Mils Wet 5.3
Mils Dry 1.8
Coverage - High 400 sq. ft.
Mils Wet 4.0
Mils Dry 1.3
Finish @ 85o < 10
Min Application Temp 50oF (10oC)
Max Application Temp 90oF (32oC)
Dry To Touch 1 hour
Dry To Recoat 2 hours
Max Tint Gallon: 2 oz
Five Gallon: 10 oz
VOC 50 g/L
Brush Nylon / Poly
Roller - Smooth 3/8" - 1/2" nap
Roller - Porous 1/2" - 3/4" nap
Spray Tip .015" - .021"
Spray Filter 60 mesh
Spray Pressure 2,500 - 3,200
Volume Solids 33.7% (+/-) 2%
Weight Solids 52.3% (+/-) 2%
Viscosity 97 - 107 KU
Flashpoint N/A

WHERE TO USE

This production flat provides a consistent, monolithic finish with very good touch-up properties and is ideal for ceilings and walls over properly prepared:

  • Drywall
  • Masonry
  • Concrete Block
  • Poured Concrete
  • Cured Plaster
  • Architectural Plastics
  • CMU
  • Metal
  • Wood

SURFACE PREPARATION†
  • All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew stains, loose and peeling paint, rust and all other foreign substances. Glossy surfaces must be 'scuff sanded' with appropriate sandpaper prior to coating.
  • Fill all gaps with a 100% acrylic, siliconized, paintable caulking and allow to completely dry prior to coating.


APPLICATION
  • Use product when surface and air temperatures are between 35 – 90oF (2-32oC).
  • Apply using a brush, roller or sprayer Stir thoroughly before and occasionally during use.
  • DO NOT THIN – Product is formulated for use at package consistency only.
  • Intermix containers of same product to ensure color and sheen uniformity.
  • Some colors may require more than one coat.
  • To reduce waste, consult with your retailer or an online paint calculator to determine the correct amount of paint to purchase.

DRY TIME at 77°F (25°C), 50% RH
  • To Touch: 1 Hour
  • To Recoat: 2 Hours
  • Full Cure: 7 Days
    Longer dry time required in cooler temperatures and in higher humidity.

CLEAN UP & DISPOSAL
  • Use soap and water to clean tools, splatters and spills.
  • Spills can be contained with dry sand or other inert absorbent.
  • Do not dispose of this product down a drain.
  • Please consider donating any unused product.
  • For recycling or disposal information, contact your local refuse collection service.

 


CAUTIONS / LIMITATIONS
  • IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS
  • FOR TINT BASES – DO NOT USE WITHOUT THE ADDTION OF COLORANT
  • INTERIOR USE ONLY
  • DO NOT USE ON FLOORS
  • DO NOT USE WHEN AIR AND SURFACE TEMPERATURES ARE BELOW 35ºF OR ABOVE 90ºF
  • ALLOW 2 WEEKS FOR FULL CURE BEFORE WASHING OR CLEANING
  • SHELF LIFE UNDER NORMAL CONDITIONS IS TWO YEARS UNOPENED

 


LIMITED WARRANTY

If this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option, either furnish an equivalent amountof new product or refund the purchase price to the original consumer purchaser of this product upon proof of purchase. Masterchem Industries will not be liable for any representations or warranties made by any retail seller or applicator of this product. This warranty excludes (1) labor or cost of labor for the removal of this product or any other product, the repair or replacement of substrates to which this product is applied or the application of replacement product and (2) any incidental or consequential damages. Some states do not allow the exclusion or limitation of incidentalor consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific rights and you may also have otherrights which vary from state to state. This warranty is not transferable. To make a warranty claim, write to Technical Service, Masterchem Industries LLC, 3135Old Highway M, Imperial, MO 63052-2834, or email Technical Service at techservice@masterchem.com.


†WARNING!

If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUSILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respiratorto control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family bycontacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.

WARNING: Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.

WARNING! IRRITANT! HARMFUL OR FATAL IF SWALLOWED. CONTAINS: ETHYLENE GLYCOL. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF DUST, VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with a P-Series particulate pre-filter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.

FIRST AID

  • If swallowed, do not induce vomiting. Get medical attention immediately.
  • If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.
  • In case of eye contact, flush eyes immediately with plenty of water for at least 15 - 20 minutes and get medical attention.
  • For skin, wash thoroughly with soap and water.

KEEP FROM FREEZING
KEEP OUT OF REACH OF CHILDREN
DO NOT TAKE INTERNALLY


Back To Top Back To Top
Back To Top Back To Top