Logo

KILZ® Original Primer

KILZ® Original Primer

Bookmark and Share
      

KILZ® ORIGINAL blocks most stains including water, smoke, tannin, ink, pencil, felt marker and grease, and seals pet and smoke odors. Use on interior surfaces including wood, drywall, plaster, paneling, wallpaper, masonry, brick, painted metal and properly prepared glossy surfaces.† KILZ ORIGINAL is not recommended on flooring.

Where to Buy

Ace Hardware Find a Store
Do it Best Find a Store
The Home Depot Find a Store   Buy Now
Lowe's Find a Store   Buy Now
True Value Find a Store
Walmart Find a Store   Buy Now

   Available in
    Aerosol 1024 - MSDS   |   KILZ Original - TDS
    Quarts, Gallons & Fives 1000 - MSDS   |   KILZ Original - TDS

   Low VOC
    Low VOC 1003 - MSDS   |   KILZ Original - TDS

PRODUCT SPECIFICATIONS
Base Oil
Int/Ext Int
Color White
Coverage - Low 300 sq. ft.
Mils Wet 5.3
Mils Dry 2.3
Coverage - High 400 sq. ft.
Mils Wet 4
Mils Dry 1.7
Finish @ 85o < 10
Min Application Temp 50oF (10oC)
Max Application Temp 90oF (32oC)
Dry To Touch 30 min
Dry To Recoat 1 hour
Max Tint 2 oz
VOC 443 g/L
Low VOC Formula 344 g/L
Brush Nylon / Poly
Roller - Smooth 3/8" - 1/2" nap
Roller - Porous 1/2" - 3/4" nap
Spray Tip .015" - .021"
Spray Filter 60 mesh
Spray Pressure 2,500 - 3,000
Volume Solids 42.7% (+/-) 2%
Volume Solids
Low VOC Formula
53.1% (+/-) 2%
Weight Solids 63.9% (+/-) 2%
Weight Solids
Low VOC Formula
76.8% (+/-) 2%
Viscosity 95 - 105 KU
Flashpoint No. 1000
(75oF (23.9oC)
Flashpoint
Low VOC Formula
No. 1003
(102oF (38.9oC)

SURFACE PREPARATION†
  • Wash off any dirt, grease or smoke damage with a non-soapy detergent or a TSP substitute, rinse well and then allow to dry.
  • Remove all mildew with a commercially available mildew remover, rinse well and then allow to dry. Note: KILZ PREMIUM and KILZ 2 are recommended for mildew-prone surfaces.
  • Unpainted, exterior wood exposed to sun and/or moisture longer than 2-4 weeks must be cleaned and sanded before priming.
  • For maximum adhesion, scrape off loose paint and scuff sand the surface thoroughly before priming. On glossy surfaces: scuff sand the surface thoroughly before priming.

 


APPLICATION
  • Eye protection is recommended.
  • For best results, use when substrate and air temperatures are between 35°F (2°C) and 90°F (32°C).
  • Stir or mix prior to and during use, do not thin.
  • Prime the entire surface to ensure a uniform appearance of the topcoat.
  • Tough stains may require two coats to block completely.
  • KILZ ORIGINAL may be used on clean, dry, aged masonry surfaces that have cured (dried) at least 90 days. If masonry has cured less than 90 days, use KILZ PREMIUM, KILZ 2 or KILZ ODORLESS.
  • Coverage varies by surface. Coverage will be approximately 300 square feet per gallon on rough surfaces; up to 400 square feet per gallon on smooth, nonporous surfaces.
  • Can be tinted with up to 2 ounces of universal colorant per gallon.

 


DRY TIME at 77°F (25°C), 50% RH
  • Dries to the touch in 30 minutes at 77°F (25°C) and 50% humidity.
  • Recoat or topcoat after 1 hour.

 


CLEAN UP & DISPOSAL
  • Use mineral spirits to clean tools, spatters and spills.
  • Spills can be contained with dry sand or other inert absorbent.
  • For recycling or disposal information in your community, call 1-800-CLEANUP.

*LIMITED WARRANTY

If this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option, either furnish an equivalent amount of new product or refund the purchase price to the original consumer purchaser of this product upon proof of purchase. Masterchem Industries will not be liable for any representations or warranties made by any retail seller or applicator of this product.
 
This warranty excludes (1) labor or cost of labor for the removal of this product or any other product, the repair or replacement of substrates to which this product is applied or the application of replacement product and (2) any incidental or consequential damages.
 
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. To make a warranty claim, write to Technical Service, Masterchem Industries LLC, 3135 Old Highway M, Imperial, MO 63052-2834, or e-mail Technical Service at techservice@masterchem.com.

 


†WARNING!

This product contains chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm.
 
DANGER! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
 
CONTAINS PETROLEUM DISTILLATES. VAPOR HARMFUL:  May affect the brain or nervous system causing dizziness, headache, or nausea. Causes eye, skin, nose and throat irritation.
 
USE ONLY WITH ADEQUATE VENTILATION:  Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If you experience eye watering, headache, or dizziness, or if air monitoring demonstrates vapor / mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH / MSHA TC 23C or equivalent) during and after application. Follow respirator manufacturer’s direction for respirator use. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling and before smoking and eating.
 
NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.
 
VAPORS MAY CAUSE FLASH FIRE:  Vapors can flow along surfaces to a distant ignition source and flash back. Keep away from heat, sparks and flame. Do not smoke. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. To avoid spontaneous combustion, soak soiled rags and waste immediately after use in a closed, water filled metal container. See clean-up and disposal for more information.
 
FIRST AID: If swallowed, do not induce vomiting. Get medical attention immediately. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately. In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.
 
KEEP FROM FREEZING.  If frozen, let thaw at room temperature.
 
KEEP OUT OF REACH OF CHILDREN!


Back To Top Back To Top
Back To Top Back To Top