KILZ COMPLETE®

Seals
Porous
Surface

Promotes
Adhesion

Helps
Block/Seal
Odors

Helps
Block
Severe
Stains

Mildew
Resistant
Finish

KILZ COMPLETE® is an Oil-based Primer, Sealer and Stainblocker ideal for blocking stains, priming, and sealing almost all interior and exterior surfaces. It is especially effective at blocking graffiti, tannin, water, smoke and other bleeding stains. KILZ COMPLETE Primer dries quickly and provides a mildew resistant coating. It can be used under latex or oil-based paint. Not recommended on flooring.

Available in Quarts, Gallons & Fives

Where To Buy

Please check availability before visiting your local retailer

  • Ratings & Reviews
  • Preparation, Application & Clean-Up
  • Warranty / Warnings
  • Product Specifications

Surface Preparation

  • The surface must be clean, free of dust, grease, wax, peeling paint, mold, mildew and wallpaper paste. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.

  • Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.†

  • Unpainted, exterior wood exposed to sun and/or moisture longer than 2 - 4 weeks must be cleaned and sanded before priming.

  • Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before priming.†

  • Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.

  • Masonry, Brick, Stucco and Plaster: KILZ COMPLETE primer may be used on clean, dry, aged masonry surfaces that have cured (dried) at least 90 days. If masonry has been cured less than 90 days, use KILZ® PREMIUM primer.

  • Fire Restoration: It is critical to clean smoke damaged surfaces thoroughly before priming.

Application

  • Eye protection is recommended.                                                                                                                                                                 

  • Apply as supplied using a brush, roller or sprayer.

  • Do not thin.

  • Only apply if surface, air and product temperatures are between 10°- 32° C.

  • Stir thoroughly before and occasionally during use.

  • Prime the entire surface to ensure a uniform appearance of the topcoat.

  • Stainblocking: After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, a longer dry time is needed before topcoating.

  • Tinting: Not recommended for stainblocking applications. KILZ COMPLETE primer may be tinted with up to 60 ml of universal colourant per 3.79L for non-stainblocking projects. Tinting to a lighter shade than the topcoat is recommended.

Dry Time at 25°C, 50% RH

  • Dries to the touch in 30 minutes at 25°C and 50% humidity.

  • Recoat or topcoat after 1 hour.

Clean-Up & Disposal

  • Clean equipment and paint spatters with mineral spirits.

  • If spilled, contain material and remove with an inert absorbent.

  • Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations.

  • Do not dispose of this product down a drain.

  • Please consider donating any unused product.

  • For recycling or disposal information, contact your local household refuse collection service.

*Limited Warranty

If this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option, either furnish an equivalent amount of new product or refund the purchase price to the original consumer purchaser of this product upon proof of purchase. Masterchem Industries LLC will not be liable for any representations or warranties made by any retail seller or applicator of this product. This warranty excludes (1) labour or cost of labour for the removal of this product or any other product, the repair or replacement of substrates to which this product is applied or the application of replacement product and (2) any incidental or consequential damages. This warranty is not transferable. The above provisions are not intended to operate where prohibited by law and do not preclude the operation of any applicable provincial consumer protection statute which may in certain circumstances extend the express limited warranty made above. To make a warranty claim write to Technical Service, Masterchem Industries LLC, 3135 Old Highway M, Imperial, MO 63052-2834, USA or email Technical Service at techservice@masterchem.com.  

Warning!

This product contains chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm.
 


Danger!

If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. 



CONTAINS PETROLEUM DISTILLATES. VAPOR HARMFUL: May affect the brain or nervous system causing dizziness, headache, or nausea. Causes eye, skin, nose and throat irritation.

USE ONLY WITH ADEQUATE VENTILATION: Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If you experience eye watering, headache, or dizziness, or if air monitoring demonstrates vapor / mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH / MSHA TC 23C or equivalent) during and after application. Follow respirator manufacturer’s direction for respirator use. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling and before smoking and eating.

NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.

VAPORS MAY CAUSE FLASH FIRE: Vapors can flow along surfaces to a distant ignition source and flash back. Keep away from heat, sparks and flame. Do not smoke. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. To avoid spontaneous combustion, soak soiled rags and waste immediately after use in a closed, water filled metal container. See clean-up and disposal for more information.

First Aid

  • If swallowed, do not induce vomiting. Get medical attention immediately.

  • If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.

  • In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and get medical attention.

  • For skin, wash thoroughly with soap and water.

KEEP FROM FREEZING. If frozen, let thaw at room temperature.

KEEP OUT OF REACH OF CHILDREN!

  • Base

    Oil

  • Int/Ext

    Int/Ext

  • Color

    White

  • Coverage - Low

    28 m²

  • Mils Wet

    5.3

  • Mils Dry

    3

  • Coverage High

    37 m²

  • Mils Wet

    4

  • Mils Dry

    2.3

  • Finish @ 85°

    < 10

  • Min Application Temp

    10°C

  • Max Application Temp

    32°C

  • Viscosity

    80 - 90 KU

  • Dry To Touch

    30 min

  • Dry To Recoat

    1 hour

  • Max Tint

    60 mL per 3.79L

  • VOC

    344 g/L The addition of colourants may add VOCs.

  • Brush

    Nylon / Polyester Blend

  • Roller - Smooth

    10-12mm nap

  • Roller - Porous

    12-14mm nap

  • Spray Tip

    0.38 - 0.53mm tip

  • Spray Filter

    60 mesh

  • Spray Pressure

    2,500 - 3,000

  • Volume Solids

    56.5% (+/-) 2%

  • Weight Solids

    75.0% (+/-) 2%

  • Flashpoint

    23.3°C