KILZ® Siding, Fence And Barn Paint

KILZ® Siding, Fence and Barn Paint for all exterior vertical wood surfaces. This product provides excellent adhesion to a variety of other surfaces such as masonry and stucco. The unique water/oil base formula resists cracking, peeling and blistering.

Available in Gallons

Where To Buy

Please check availability before visiting your local retailer

  • Ratings & Reviews
  • Preparation, Application & Clean-Up
  • Warranty / Warnings
  • Product Specifications

Surface Preparation

  • Remove any mildew stains with a bleach and water solution or similar commercially available mildew remover then rinse.

  • Sand all glossy surfaces.

  • To determine the condition of the surface, place cloth duct tape in several places on the bare wood. Press the tape down firmly then remove quickly. If wood fibers or debris are pulled onto the tape, additional preparation is required as follows:

  • If debris is found using the above test, remove any loose or peeling paint† and wash off dirt or grease with a non-soapy detergent such as TSP substitute. Remove mill glaze, loose wood fibers, dirt and other debris. Rinse with water and allow to dry completely.

  • If surface is in good condition, apply directly over clean, dry surface.

Application

  • Do not use if temperature is below 50°F (10°C) or if rain is expected within 24 hours.

  • All surfaces must be completely dry.

  • Intermix containers of the same color to ensure color uniformity.

  • Many woods contain tannin which may cause discoloration. Prime these woods with one coat of KILZ PREMIUM to reduce these stains as needed.

  • Coverage varies by porosity. Coverage will be approximately 200 square feet per gallon on porous surfaces; up to 500 square feet per gallon on smooth, nonporous surfaces.

  • Keep a wet edge and always back-brush or back-roll during all application methods.

  • Airless Spray - .015 to .017 tip.

  • Brush - Use a high quality Nylon/Polyester brush.

  • Rolling - Use a high quality 3/8-1/2" nap roller cover on smooth surfaces or 1/2-3/4" nap roller cover on semi-rough or porous surfaces.

Dry Time

  • Dries to the touch in 2-3 hours.

  • Allow 6 to 8 hours of drying prior to recoating.

Clean up & Disposal

  • Use soap and water to clean hands, tools, and spills.

  • Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.

Cautions/Limitations

  • Protect from freezing.

  • Not for use on horizontal surfaces subject to foot traffic.

  • For best results, apply at temperatures between 50 - 90°F. Temperatures above 90°F may affect the application such as drying too fast. Avoid painting in direct sun. NOTE: If the surface is hot to the touch it should be considered too hot to apply this coating.

  • Avoid heavy traffic for 24 hours.

  • Allow two weeks before washing or cleaning for full cure.

  • Shelf life under normal conditions is two years unopened.

*Limited Warranty

If this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option, either furnish an equivalent amount of new product or refund the purchase price to the original consumer purchaser of this product upon proof of purchase. Masterchem Industries will not be liable for any representations or warranties made by any retail seller or applicator of this product. This warranty excludes (1) labor or cost of labor for the removal of this product or any other product, the repair or replacement of substrates to which this product is applied or the application of replacement product and (2) any incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. To make a warranty claim, write to Technical Service, Masterchem Industries LLC, 3135 Old Highway M, Imperial, MO 63052-2834, or e-mail Technical Service at techservice@masterchem.com.

General Information

IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS

Warning!

If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

Warning! Irritant!

HARMFUL IF SWALLOWED. CONTAINS: ETHYLENE GLYCOL. MAY CAUSE EYE, NOSE AND THROAT IRRITATION.AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air and use a properly fitted respirator (NIOSH approved for zorganic vapor with P Series particulate prefilter). Obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.

First Aid

  • If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
  • In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention.
  • For skin, wash thoroughly with soap and water.
  • If swallowed, get medical attention immediately.

Caution

  • KEEP OUT OF REACH OF CHILDREN
  • DO NOT TAKE INTERNALLY
  • Base

    Red, White

  • Int/Ext

    Ext

  • Color

    Red, White

  • Coverage Rate

    200-500 sq. ft./gal., depending on application method and substrate porosity. Does not include the loss of material from spraying.

  • Coverage - Low

    200 sq. ft.

  • Mils Wet

    8

  • Mils Dry

    2.7

  • Coverage High

    500 sq. ft.

  • Mils Wet

    3.2

  • Mils Dry

    1.1

  • VOC

    100 g/L

  • Volume Solids

    35%

  • Weight Solids

    49%

  • Viscosity

    87-93 KU

  • Flashpoint

    N/A