KILZ® Color Change Ceiling Paint

KILZ® STAINBLOCKING CEILING PAINT is a unique combination of stainblocking technology and a coverage/dry time indicator. It rolls on easily with minimal spattering and a subtle pink color that quickly dries to white. It can be used on all interior ceilings.

Available in Gallons

Where To Buy

Please check availability before visiting your local retailer

  • Ratings & Reviews
  • Preparation, Application & Clean-Up
  • Warranty / Warnings
  • Product Specifications

Preparation

  • Remove any mildew stains with bleach and water solution or similar commercially available mildew remover, then rinse.

  • Scuff sand glossy surfaces.

  • Remove loose paint and wash off any dirt or grease with a non-soapy detergent such as trisodium phosphate (TSP).

  • Make sure that there are no active water problems and that any previous water damage is fully dry. KILZ® ORIGINAL, KILZ COMPLETE® or KILZ ODORLESS® Primer is recommended for blocking severe stains.

Application

  • Use only when temperatures are between 50°F (10°C) and 90°F (32˚C).

  • Stir paint prior to use.

  • Coverage varies by porosity. Coverage will be approximately 250 square feet per gallon on porous surfaces; up to 400 square feet per gallon on smooth, nonporous surfaces.

  • Use quality Nylon/Polyester brush and 3/8" - 1/2" nap quality roller depending on surface texture.

  • Multiple coats may be required for complete hide.

Dry Time

  • Color indicator will fade to white in under 1 hour.

  • Dries to the touch in 1 hour at 77°F (25°C) and 50% humidity.

  • Recoat as needed after 2 hours, for maximum stainblocking, recoat after 4 hours.

Clean-Up & Disposal

  • Use soap and water to clean hands, tools and spills.

  • Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.

Cautions / Limitations

  • Eye protection is recommended.

  • Only apply if surface, air and product temperatures are between 50°-90°F (10°-32°C).

  • Stir thoroughly before and occasionally during use.

  • Stainblocking: Multiple coats may be required for complete stainblocking and hide.

*Limited Warranty

For one year from the date of purchase, Masterchem Industries LLC warrants to the original residential consumer purchaser (1) that the product meets Masterchem Industries LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event that this product proves to be defective within one year from the date of purchase, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.  Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

General Information

IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS

Warning!

If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

Warning! Irritant!

HARMFUL IF SWALLOWED. CONTAINS: ETHYLENE GLYCOL. MAY CAUSE EYE, NOSE AND THROAT IRRITATION.AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air and use a properly fitted respirator (NIOSH approved for zorganic vapor with P Series particulate prefilter). Obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.

First Aid

  • If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
  • In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention.
  • For skin, wash thoroughly with soap and water.
  • If swallowed, get medical attention immediately.

Caution

  • KEEP OUT OF REACH OF CHILDREN
  • DO NOT TAKE INTERNALLY
  • Color

    White

  • Coverage Rate

    250 - 400 sq. ft. (23 - 37 m2) per gallon, depending on the surface texture, porosity and application method. Does not include the loss of material from spraying.

  • Coverage - Low

    250 sq. ft.

  • Mils Wet

    6.4

  • Mils Dry

    2.4

  • Coverage High

    400 sq. ft.

  • Mils Wet

    4

  • Mils Dry

    1.5

  • VOC

    50 g/L

  • Volume Solids

    42%

  • Weight Solids

    56%

  • Viscosity

    95-105 KU

  • Flashpoint

    N/A