Logo

Smooth Enamel Finish

Smooth Enamel Finish
Bookmark and Share
      

HAMMERITE® RUST CAP® SMOOTH ENAMEL FINISH is a self-priming, rust preventive coating designed to provide long-lasting metal protection. It provides a decorative finish that resists corrosion and the damaging effects from moisture and severe weather, and is formulated for interior and exterior use.


   Colors
    Smooth Almond Brush Grade Enamel Finish 44200 - MSDS
    Smooth Almond Aerosol Enamel Finish 42200 - MSDS
    Smooth Aluminum Brush Grade Enamel Finish 44205 - MSDS
    Smooth Aluminum Aerosol Enamel Finish 42205 - MSDS
    Smooth Bright Red Brush Grade Enamel Finish 44210 - MSDS
    Smooth Bright Red Aerosol Enamel Finish 42210 - MSDS
    Smooth Bright Yellow Brush Grade Enamel Finish 44215 - MSDS
    Smooth Bright Yellow Aerosol Enamel Finish 42215 - MSDS
    Smooth Dark Blue Brush Grade Enamel Finish 44225 - MSDS
    Smooth Dark Blue Aerosol Enamel Finish 42225 - MSDS
    Smooth Dark Green Brush Grade Enamel Finish 44230 - MSDS
    Smooth Dark Green Aerosol Enamel Finish 42230 - MSDS
    Smooth Flat Black Brush Grade Enamel Finish 44235 - MSDS
    Smooth Flat Black Aerosol Enamel Finish 42235 - MSDS
    Smooth Gloss Black Brush Grade Enamel Finish 44240 - MSDS
    Smooth Gloss Black Aerosol Enamel Finish 42240 - MSDS
    Smooth Gray Brush Grade Enamel Finish 44245 - MSDS
    Smooth Gray Aerosol Enamel Finish 42245 - MSDS
    Smooth Light Blue Brush Grade Enamel Finish 44250 - MSDS
    Smooth Light Blue Aerosol Enamel Finish 42250 - MSDS
    Smooth White Brush Grade Enamel Finish 44260 - MSDS
    Smooth White Aerosol Enamel Finish 42260 - MSDS
    Smooth Flat White Aerosol Enamel Finish 42270 - MSDS
    Smooth Blue Aerosol Enamel Finish 42290 - MSDS
    Smooth Blue Brush Grade Enamel Finish 44290 - MSDS

 

Where to Use
  • For use on metal substrates.
  • Can be applied directly over firm, rusty surfaces.
  • For previously painted surfaces, apply HAMMERITE® RUST CAP® SMOOTH ENAMEL FINISH to a small area first to check adhesion and test for lifting or cracking.

Surface Preparation†
  • Prepare surface by removing dirt, grease, wax, moisture, rust, loose paint and any other contamination that can affect the coating's adhesion. If washing is necessary, use a non-soapy detergent or TSP substitute. Rinse well and allow to dry. 
  • Scrape off loose paint and rust with a wire brush.
  • Scuff sand rusted, glossy or hard surfaces.†

 


Priming
  • Aluminum and galvanized surfaces require a prime coat of HAMMERITE® RUST CAP® GALVANIZED & ALUMINUM PRIMER.

 


Application
  • Eye protection is recommended.
  • Do not thin.
  • Use in a well-ventilated area when temperature is between 60°F and 80°F and humidity is below 60% to ensure proper drying.
  • Mix paint thoroughly before and during application.
  • Always maintain a wet edge, but avoid over-brushing and/or rolling.
  • Apply 2 or more coats as needed to achieve the 4 mil dry film thickness.
  • Recoat after the first coat has dried to the touch (30-45 minutes).
  • Use a high quality ¼” nap Mohair cover on smooth surfaces. A quality synthetic bristle brush can also be used.
  • Airless Spray: Use .017-.021 tip size at approximately 1800-2600 psi.
  • Conventional Spray: Use 70-80 thousandths tip size, pot pressure 15-20 psi and atomizing pressure 25-35 psi.

 


Dry Time & Coverage
  • Each additional coat must be applied within 4 hours or after 14 days of drying.
  • Dries to the touch in 90 minutes.
  • Coverage is approximately 200 sq. ft. per gallon depending on the method of application, porosity and texture of the surface (to achieve a 4 mil dry film thickness).

 


Clean Up & Disposal
  • Clean all tools, equipment and paint spatters with Xylene or lacquer thinner.
  • If spilled, contain material and remove with an inert absorbent.
  • Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations.
  • Do not dispose of this product down a drain.
  • Please consider donating any unused product.
  • For recycling or disposal information, contact your local household refuse collection service.

 


Aerosol Application
  • Use outdoors or in a well-ventilated area when temperature is between 60°F and 80°F and humidity is below 60% to ensure proper drying. Avoid spraying in very windy or dusty conditions.
  • Shake can vigorously for 2 minutes after mixing ball begins to rattle and often during use. Hold can upright, moving from side-to-side while spraying lightly and evenly about 12” from area being painted. Ensure corners, edges and heavily pitted areas are adequately covered. Apply 3 or more light coats allowing 10 to 15 minutes between coats.

 


Aerosol Dry Time & Coverage
  • Dries in 15 minutes or less.
  • Handle after one hour.
  • Recoat should be done within 1 hour or after 10 days.
  • A 4 mil coating cures in 14 days.
  • Coverage is up to 18 sq. ft.

 


Aerosol Clean Up & Disposal
  • Clear spray valve immediately after use by turning can upside down and spraying until only clear gas is released.
  • If spray nozzle becomes clogged, remove and clean with mineral spirits. Gently replace spray button with a twisting motion, with top of can and valve opening pointed away from you. Do not stick pins or wire into can opening.
  • Do not dispose of this product down a drain.
  • Please consider donating any unused product.
  • For recycling or disposal information, contact your local household refuse collection service.

 


Glassguard® Protection
  • As the coating dries, microscopic heat-hardened glass flakes interlock with special resins forming a super-tough barrier that seals out moisture to prevent rusting.

 


*Limited Warranty

In lieu of all other warranties and guarantees, if this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option, either furnish an equivalent amount of new product or refund the purchase price to the original consumer purchaser of this product upon proof of purchase. Masterchem Industries will not be liable for any representations or warranties made by any retail seller or applicator of this product. This warranty excludes (1) labor or cost of labor for the removal of this product or any other product, the repair or replacement of substrates to which this product is applied or the application of replacement product and (2) any incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. To make a warranty claim, write to Technical Service, Masterchem Industries, 3135 Old Highway M, Imperial, MO 63052-2834, or e-mail Technical Service at techservice@masterchem.com


†WARNING!

If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1- 800-424-LEAD or log on to www.epa.gov/lead.

WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects, or other reproductive harm.

IRRITANT! HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING.USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.

CONTAINS XYLENE, PETROLEUM DISTILLATES, PROPANE, ISOBUTANE, ACETONE, N-BUTANE. Vapor harmful. May affect the brain or nervous system causing dizziness, headache or nausea. Causes eye, skin, nose and throat irritation. Harmful if absorbed through skin. Can cause nerve damage to arms and legs. Effects may be permanent. Do not puncture or incinerate (burn) container. Exposure to heat or prolonged exposure to sun may cause bursting. Do not expose to heat or store at temperatures above 120°F.

NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.

Vapors may ignite explosively. Keep away from heat, sparks and flame.

Vapors may cause flash fire. Do not smoke. Extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation.

FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.

KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.


Back To Top Back To Top