PRODUCTS

KILZ® Weatherproofing Transparent Finish

KILZ® Weatherproofing Transparent Wood Finish penetrates into wood to deliver complete protection from the elements for up to 4 years on decks and 6 years on fences and siding. The silicone-fortified, 100% acrylic formula delivers excellent protection from the sun’s harmful UV rays. For new to slightly weathered wood substrates, this product is ideal for properly prepared, unsealed exterior surfaces such as: decks, railings, shakes, shingles, siding, fences and wood patio furniture.

WHERE TO BUY

Please check availability before visiting your local retailer

L8200
L8201
L8202

Available in Gallons

Preparation†

The following steps and products are required.

  • All surfaces must be clean, dry and free of any dirt, oil and grease.

  • Scuff sand any glossy surfaces. If making repairs, use stainless steel or galvanized nails to prevent nail staining. Countersink nail heads, repair imperfections and sand smooth. Remove all dust with a damp cloth and allow to dry.

  • New and Weathered Wood: Use a product such as KILZ Wood Cleaner & Brightener to open wood pores for better penetration and remove any mill glaze and mildew stains. Remove remaining wood fibres and debris by sanding lightly.

  • Painted Wood Surfaces: To strip previous coating, use a product such as KILZ Wood Stain & Finish Stripper. Then clean and neutralize with a product such as KILZ Wood Cleaner & Brightener.

  • After using KILZ Wood Cleaner & Brighter or KILZ Wood Stain & Finish Stripper, rinse thoroughly with a garden hose or pressure washer. When rinsing with a pressure washer, use the broadest spray pattern while keeping the nozzle at least 0.6 m away from the surface. Allow the area to dry at least 24 hours before coating. Lightly sand to remove remaining wood fibers/fuzz.

WARNING! Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.
 

Application

  • Avoid applying in direct sunlight or to hot surfaces.

  • Must apply between 4.5°C - 32°C. Do not use if rain is expected within 24 hours.

  • The wood surface must be completely dry before application.

  • Intermix multiple containers to ensure colour uniformity. DO NOT DILUTE. Stir product occasionally throughout application.

  • Test product for penetration and colour on a small hidden area before proceeding.

  • Use a nylon/polyester brush for areas requiring more accuracy. Use of rollers should be limited to rough surfaces only. Use 10 mm nap or longer when appropriate.

  • A high quality pump sprayer with a variable tip or an airless sprayer with a .015"-.019" tip (60 mesh filter recommended) may be used.

  • Work in small sections lightly saturating the surface and immediately back-brush or use pad applicator to eliminate puddling, remove excess and evenly distribute the finish. Maintain a wet edge when applying.

  • Apply product end-to-end or to board lengths to prevent lap marks. Over application of finish will lead to surface failure including peeling and cracking. Avoid applying finish too heavily.

  • Two thin coats required. For optimum performance, coat all accessible sides.

  • COVERAGE: 1st Coat 23 m² - 32 m²; 2nd Coat 56 m² - 65 m².

Dry Time

  • Wait 1-2 hours before recoating. Fully cured coating can be washed after 72 hours.

  • Additional dry time may be needed in cooler temperatures and higher humidity.

Clean up & Disposal

  • Clean equipment and paint spatters with warm, soapy water. If spilled, contain material and remove with an inert absorbent.

  • Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations.

  • Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.

Cautions / Limitations

  • Protect from freezing.

  • Do not use if rain is expected within 24 hours.

  • DO NOT THIN PRODUCT.

  • Avoid applying paint in direct sunlight or hot surfaces.

  • Test product for colour on a small hidden area before proceeding.

  • Over application of stain will lead to surface failure including peeling & cracking.

  • Stained surfaces may become slippery when wet.

  • Shelf life under normal conditions is 2 years (unopened containers).

  • Temperature Range: 4.5°C - 32°C.