KILZ COMPLETE® Interior / Exterior Aerosol Primer
KEY ATTRIBUTES - LEARN MORE
KILZ COMPLETE® is a premium quality primer, sealer and severe stain blocker for both interior/exterior use. It is ideal for blocking severe fire and smoke damage, tannins from Cedar and Redwood and other bleeding stains. KILZ COMPLETE offers great penetration and adhesion, quick dry time and a dry film that is mold resistant. COMPLETE may be topcoated with latex or oil-base paint.
The following steps are required for product performance.
The surface must be clean, free of dust, grease, wax, peeling paint, mold, mildew and wallpaper paste. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.
Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.†
Unpainted, exterior wood exposed to sun and/or moisture longer than 2-4 weeks must be cleaned and sanded before priming.
Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before priming.†
Eye protection is recommended.
For best results, use when substrate and air temperatures are between 2°C and 32°C.
Cover adjacent areas to protect from overspray.
Prime the entire surface to ensure a uniform appearance of the topcoat.
Shake can vigorously for 1 minute after mixing ball begins to rattle and often during use.
Hold can upright, moving from side-to-side while spraying lightly and evenly about 30 cm from area being painted.
Two to three thin coats produce best results.
Topcoat with latex or oil-based paint after 1 hour.
Dries to the touch in 30 minutes at 25°C and 50% humidity.
Finishing: Topcoat within 30 days to prevent contamination of the primer before painting.
NOTE: On some surfaces, spot priming may cause a non-uniform appearance in the final coat. To avoid this, prime the entire surface.
Dry Time at 25°C, 50% RH
To Touch: 15 - 30 Minutes
To Recoat / Topcoat: 1 Hour
Longer dry time may be required in cooler temperatures and in higher humidity.
Clean-Up & Disposal
Do not stick pins or wire into can opening.
Clean fresh overspray with mineral spirits or paint thinner. Remove dried paint with paint remover, but test small area first to ensure paint remover does not damage substrate.
Please consider donating any unused product.
For recycling or disposal information, contact your local household refuse collection service.
1.9 m² - 2.3 m²
Finish @ 85°
Min Application Temp
Max Application Temp
Dry To Touch
15 - 30 min
Dry To Recoat
60% Max by weight
16.8% (+/-) 2%
37.1% (+/-) 2%
If this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option, either furnish an equivalent amount of new product or refund the purchase price to the original consumer purchaser of this product upon proof of purchase. Masterchem Industries LLC will not be liable for any representations or warranties made by any retail seller or applicator of this product. This warranty excludes (1) labour or cost of labour for the removal of this product or any other product, the repair or replacement of substrates to which this product is applied or the application of replacement product and (2) any incidental or consequential damages. This warranty is not transferable. The above provisions are not intended to operate where prohibited by law and do not preclude the operation of any applicable provincial consumer protection statute which may in certain circumstances extend the express limited warranty made above. To make a warranty claim write to Technical Service, Masterchem Industries LLC, 3135 Old Highway M, Imperial, MO 63052-2834, USA or email Technical Service at firstname.lastname@example.org.
If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
VENTILATION REQUIRED: To avoid inhalation and combustion hazards (see below), DO NOT use this product unless you can achieve cross-ventilation by opening windows and doors during application and drying.
CONTAINS PETROLEUM DISTILLATES. VAPOR HARMFUL: May affect the brain or nervous system causing dizziness, headache or nausea. Do not breathe vapors or spray mist. If you experience eye watering, headaches or dizziness, increase fresh air, wear respiratory protection (NIOSH / MSHA TC 23C or equivalent) or leave the area.
NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.
VAPORS MAY IGNITE EXPLOSIVELY. Do not spray near sparks, heat or open flame. Do not smoke. Vapors are heavier than air, and can travel at floor level to distant ignition sources. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors, high intensity lights and other sources of ignition during use and until all vapors are gone.
CONTENTS UNDER PRESSURE: Do not puncture, incinerate (burn) or store above 120°F (40°C). Exposure to heat or prolonged exposure to sun may cause bursting. Do not discard in home trash compactor.
This product contains chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
- If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.
- In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and get medical attention.
- For skin contact, wash thoroughly with soap and water.
KEEP OUT OF REACH OF CHILDREN
DO NOT TAKE INTERNALLY