KILZ® 1-Part Epoxy Acrylic Concrete & Garage Floor Paint

KILZ® 1-Part Epoxy Concrete & Garage Floor Paint is a single-component water-based epoxy. This high-performance formula resists hot tire pick-up, scuffing, fading, cracking, peeling and blistering. Can be applied to interior/exterior surfaces such as porous concrete, masonry, stone and brick. For use on horizontal surfaces such as garage floors, driveways, basements, porches and pool decks. DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. DO NOT use on areas subject to fork-lifts. For residential applications only.

WHERE TO BUY

Please check availability before visiting your local retailer

L3771
L3773
L3776
L3777

Available in Gallons

Preparation†

The following steps and products are required.

  • New and Uncoated Concrete or Masonry Surfaces:
    New concrete must cure for a minimum of 30 days. For proper penetration and adhesion of topcoat, use a product such as KILZ Concrete & Masonry Cleaner & Etcher to clean and etch the surface. Apply a product such as KILZ Concrete & Masonry Bonding Primer to increase adhesion of topcoat to the surface.

  • Painted, Stained or Sealed Concrete:
    Option 1- To completely strip the entire surface, use a product such as KILZ Concrete & Masonry Paint Stripper.
    Option 2- To recoat over an existing coating, remove any loose or peeling paint and scuff sand the surface. Use a product such as KILZ Concrete & Masonry Cleaner & Degreaser to clean previously coated surfaces in sound condition. Use a product such as KILZ Concrete & Masonry Cleaner & Etcher to clean and etch any bare concrete area.

Application

  • DO NOT DILUTE.

  • USE ONLY WITH ADEQUATE VENTILATION.

  • Intermix all cans of same product to ensure colour uniformity. Stir before applying.

  • For best results, apply when air and surface temperatures are between 10°C - 32°C.

  • Apply a thin, even coat using a 10 mm nap roller cover, pad applicator or a nylon/polyester brush or an airless sprayer (.015"-.021" spray tip, 60 mesh filter).

  • COVERAGE: 37 m² - 46 m² per 3.79 L on smooth surfaces and of 23 m² - 37 m² per 3.79 L on rough surfaces.

  • Allow first coat to dry 24 hours before deciding if a second coat is necessary. For uniformity, apply a second coat (in a criss-cross direction).

  • DO NOT APPLY MORE THAN TWO COATS. An annual touch-up may be required in areas subject to tire traffic.

Dry Time

  • Dries to touch in 2 hours. Longer dry time required in cooler temperatures and in higher humidity.

  • Re-coat time 4-6 hours.

  • The floor may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting surface to heavy foot traffic or repositioning furniture.

  • Allow 7 days before subjecting to automotive tires. Premature heavy traffic will cause paint failure requiring spot recoating. If necessary, corrugated cardboard may be used underneath automobile tires after 72 hours.

  • Wait at least 30 days before rinsing or cleaning. Use a mild detergent as needed. Abrasive cleaners and pressure-washers should be used carefully to avoid premature paint failure.

Clean up & Disposal

  • Clean all tools and equipment with soap and clean water.

  • If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations.

  • Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.

Cautions/Limitations

  • Protect from freezing.

  • For best results, apply at temperatures between 10°C - 32°C. Temperatures above 32°C may affect the application such as drying too fast. Avoid applying in direct sun. NOTE: If the surface is hot to the touch it should be considered too hot to apply this coating.

  • Avoid heavy traffic for 24 hours.

  • DO NOT APPLY MORE THAN TWO COATS.

  • Allow 30 days before washing or cleaning for full cure.

  • Shelf life under normal conditions is two years unopened.